Sensors

DESCRIPTIONThis dust sensor is sensitive enough to detect small particles in the air, 1 micrometre in diameter. The sensor gives out a PWM output t...

DESCRIPTION The Gas Sensor module is useful for gas leakage detecting(in home and industry). The MQ2 sensor can detect LPG, i-butane, methane, alco...

DESCRIPTION The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electric...

DESCRIPTIONSwipe, tap or flick your wrist to control your Raspberry Pi with the Flick HAT. Flick is a 3D tracking and gesture HAT that lets you ...

DESCRIPTION The Grove-VOC and eCO2 Gas Sensor-SGP30 is an air quality detection sensor. This grove module is based on SGP30, it provides TVOC(Total...

DESCRIPTION The Grove - 2-Channel Inductive Sensor is based on Texas Instruments(TI) LDC1612, a 28-bit inductance to digital converter(LDC) for ind...

DESCRIPTION This board provides a sensor for CO2, temperature and Relative Humidity measurements to a BBC micro:bit. FEATURES CO2 Concentrations S...

DESCRIPTIONThis is a breakout board for the 3 axis ADXL335 accelerometer from Analog Devices.This is the latest in a long, proven line of analog se...

DESCRIPTIONThe Sharp GP2Y0A21YK IR Range Sensor takes a continuous distance reading and reports the distance as an analog voltage with a distance r...

DESCRIPTION This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything...

DESCRIPTIONThis 12-inch (30-cm) cable has 26 AWG wires and a 3-pin female JST PH-style connector that mates with the connector on 3-pin Sharp analo...

DESCRIPTION This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis accele...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page ...

DESCRIPTIONThis is a three axis accelerometer for the LilyPad system. Based on the ADXL335 accelerometer from Analog Devices, the LilyPad Accelerom...

DESCRIPTIONThis is a breakout board for the incredibly small TMP102 digital temperature sensor. The TMP102 is a digital sensor (I2C a.k.a. TWI), ha...

DESCRIPTIONThe Minisense 100 is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful f...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page ...

DESCRIPTIONThis is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much press...

DESCRIPTION This is a breakout board for InvenSense's ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope. The ITG-3200 features ...

DESCRIPTIONThis is the latest DS18B20 1-Wire digital temperature sensor from Maxim IC. Reports degrees C with 9 to 12-bit precision, -55C to 125C (...

DESCRIPTIONThis tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom p...

DESCRIPTION This non invasive current sensor is a current clamp that can be used to detect a current of up to 30A. Simply clip it around the curren...

DESCRIPTIONThis is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pr...

DESCRIPTIONThis is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance dependin...